Removal and installation of a beam of a back suspension bracket. Nissan Almera (from 1995 to 1999 of release)
Nissan Almera service from 1995 to 2000 in N15 body
1. General information
2. The general requirements to car repairs
3. Operation and car maintenance
4. Petrol engines
5. Diesel engines
6. Transmission
7. Running gear
7.1. Forward suspension bracket
7.2. Back suspension bracket
7.2.1. Removal and installation of a rack of a back suspension bracket
7.2.2. Dismantling and assembly of a rack of a back suspension bracket
7.2.3. Removal and installation of a beam of a back suspension bracket
7.2.4. Replacement of a nave of a back wheel
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 







993f9bf4 993f9bf4 993f9bf4 canada online pharmacies

7-2-3-snyatie-i-ustanovka-balki-zadnejj-podveski.html

7.2.3. Removal and installation of a beam of a back suspension bracket


Fig. 5.12. Back suspension bracket: And — with a drum-type brake; B — with a disk brake; 1 — a cross-section beam; 2 — a nut of a rod of the shock-absorber; 3 — the plug; 4 — a lining of the top support; 5 — the top support of the shock-absorber; 6 — the top basic cup of a spring; 7 — the buffer of a course of compression; 8 — a protective cover; 9 — a suspension bracket spring; 10 — the shock-absorber; 11 — a brake board; 12 — a nave; 13 — a washer; 14 — a nut of fastening of a nave; 15 — шплинт; 16 — jet draft; 17 — the cross-section lever


At work be guided fig. 5.12 and 5.17.

Fig. 5.17. Sizes of the cross-section lever of a back suspension bracket and jet draft: And — the cross-section lever; B — jet draft; and = 207 — 208 mm; = 394 — 395 mm; in = 601 — 603 mm; g = 106 — 108 mm


The big opening of jet draft serves for fastening to a suspension bracket beam; a small opening — for fastening to the cross-section lever of a suspension bracket.
Lift a back part of the car and establish on supports. Remove the back
wheels. Pump out a syringe liquid from a tank of brake system. Disconnect brake hoses and wheel sensors (in the presence of ABS).

Fig. 5.18. Fastening of the cross-section lever of a back suspension bracket: 1 — a bolt of fastening of the cross-section lever to a body; 2 — a bolt of fastening of the cross-section lever to a beam of a back suspension bracket; 3 — bolts of fastening of jet draft


Fig. 5.14. A bolt of fastening of a rack of a back suspension bracket to a beam of a back suspension bracket


Disconnect a cable of the parking brake from brake mechanisms from both parties. Release a cable from clamps on a suspension bracket beam. Prop up a beam of a back suspension bracket, using a jack or supports. Turn out a bolt 1 (fig. 5.18) of fastening of the cross-section lever to a body. Turn out bolts of fastening of telescopic racks to a back beam (see fig. 5.14). Turn out bolts of fastening of longitudinal levers of a beam to a body and carefully lower a beam of a back suspension bracket.
Installation carry out in sequence, with return to removal, thus replace everything самоконтрящиеся nuts. Tighten carving connections by the set moments specified in appropriate section. Pump over brake system and adjust the parking brake. Check corners of installation of back wheels.

«previous page
7.2.2. Dismantling and assembly of a rack of a back suspension bracket
following page»
7.2.4. Replacement of a nave of a back wheel