Replacement of the bearing of a nave of a forward wheel. Nissan Almera (from 1995 to 1999 of release)
Nissan Almera service from 1995 to 2000 in N15 body
1. General information
2. The general requirements to car repairs
3. Operation and car maintenance
4. Petrol engines
5. Diesel engines
6. Transmission
7. Running gear
7.1. Forward suspension bracket
7.1.1. Removal and installation of a rack of a forward suspension bracket
7.1.2. Dismantling and assembly of a rack of a forward suspension bracket
7.1.3. Removal and installation of the stabilizer of cross-section stability
7.1.4. Removal and installation of a cross-piece of a forward suspension bracket
7.1.5. Check and adjustment of corners of installation of forward wheels
7.1.6. Replacement of the bearing of a nave of a forward wheel
7.2. Back suspension bracket
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 









993f9bf4 993f9bf4 993f9bf4 online canadian pharmacies

7-1-6-zamena-podshipnika-stupicy-perednego-kolesa.html

7.1.6. Replacement of the bearing of a nave of a forward wheel

       NOTES
Bearings are recommended to be changed from both parties of the car at the same time.
At bearing replacement it collapses and is not subject to a reuse.


Establish on supports a forward part of the car, remove a wheel. Unscrew two bolts of fastening of a brake support, remove it, without disconnecting a brake hose, and fix in a wheel arch.

Fig. 5.9. Opravki for a vypressovka of the bearing of a nave of a wheel: And — an opravka for a nave vypressovka; B — an opravka for a vypressovka and a press fitting of the bearing of a nave; In — an opravka for cuff installation


If on the car the anti-blocking system (ABS) is established, release a wire of the sensor and remove the sensor. Block from rotation a wheel nave. Take out шплинт lock-nuts and unscrew a nut of fastening of a nave. Unscrew a nut of fastening of a finger of the spherical hinge of steering bent for to a rotary fist and by means of a stripper take out a hinge finger from a rotary fist. Unscrew a nut of fastening of the bottom spherical hinge of the lever of a suspension bracket and by means of a stripper take out a hinge finger from a rotary fist. Remove a brake disk. Unscrew two bolts of fastening of a rack of a forward suspension bracket to a rotary fist and remove a rotary fist assembled with a nave. Press by means of an opravka (fig. 5.9, A) a nave from a rotary fist. Using a stripper with captures for external gearing, take from a nave an internal ring of the bearing.
Thin screw-driver take out bearing cuffs. Remove a lock ring of the bearing. Vypressuyte by means of an opravka (fig. 5.9, B) an external ring of the bearing from a rotary fist. Before installation of the new bearing carefully clear a nave and a bearing seat in a rotary fist. Check a technical condition of working surfaces — on them there should not be wear tracks and scratches. Apply a thin film greasings on an external ring of the new bearing.

Fig. 5.10. A bearing press fitting in a rotary fist: 1 — an opravka; 2 — the bearing of a nave of a wheel; 3 — a rotary fist; 4 — a support


By means of a press and an opravka press against the stop the bearing in a rotary fist, resting against an external ring of the bearing (fig. 5.10).

Fig. 5.11. A nave press fitting in a rotary fist: 1 — an opravka; 2 — the bearing of a nave of a wheel; 3 — a rotary fist; 4 — a support; 5 — a wheel nave; 6 — an external cuff; 7 — an internal cuff


Establish into place a lock ring. Press at first external, then internal bearing cuffs by means of an opravka (fig. 5.9, B), having put previously a greasing layer on edges of cuffs. Substitute an emphasis under an internal ring of the bearing and by means of a press press a nave in a rotary fist (fig. 5.11). Other operations carry out as it should be, the return to dismantling, replace everything самоконтрящиеся nuts and шплинты lock-nuts of fastening of a nave. Observe the established moments of an inhaling of carving connections.
After the completion of assembly check and if necessary adjust corners of installation of forward wheels.

«previous page
7.1.5. Check and adjustment of corners of installation of forward wheels
following page»
7.2. Back suspension bracket