Removal and installation of an automatic transmission. Nissan Almera (from 1995 to 1999 of release)
Nissan Almera service from 1995 to 2000 in N15 body
1. General information
2. The general requirements to car repairs
3. Operation and car maintenance
4. Petrol engines
5. Diesel engines
6. Transmission
6.1. Coupling
6.2. Mechanical transmission
6.3. Automatic transmission
6.3.1. General information
6.3.2. Adjustment of a cable of system of compulsory return gear shifting («kick down»)
6.3.3. Adjustment of a cable of a drive of the selector
6.3.4. Adjustment of the selector of a transmission
6.3.5. Removal and installation of an automatic transmission
6.4. Drive of forward wheels
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 









993f9bf4 993f9bf4 993f9bf4 canadian health care mall

6-3-5-snyatie-i-ustanovka-avtomaticheskojj-korobki-peredach.html

6.3.5. Removal and installation of an automatic transmission


Fig. 4.46. Details of the mechanism of gear shifting: 1 — draft of the selector of a transmission; 2 — the lever of compulsory return gear shifting; 3 — a selector cam; 4 — a lamellar spring of the reduktsionny valve; 5 — the switch of the blocking device of a starter; 6 — a selector cable; 7 — sector of the lever of the selector; 8 — the blocking button; 9 — the handle of the lever of the selector; 10 — a control lamp of inclusion of transfer; 11 — a spring; 12 — an arm; 13 — laying; 14 — a cable of compulsory return gear shifting; 15 — draft of a drive of the position "R" of the lever of the selector


Fig. 4.52. Details of a case of an automatic transmission: 1 — connecting draft; 2 — the hydrotransformer; 3 — a hydrotransformer case; 4 — masloizmeritelny щуп; 5 — a directing tube; 6 — a regulator; 7 — a transmission case; 8 — laying; 9 — a lateral cover; 10 — a stopper of a masloslivny opening; 11 — the pallet; And — to an oil radiator


Fig. 4.50. Placement of a stopper of a masloslivny opening of an automatic transmission


Fig. 4.51. Otvorachivaniye of bolts of fastening of the hydrotransformer to a leading disk


At works be guided fig. 4.46 and 4.52. Remove the storage battery, previously having disconnected wires. Remove the assembly block under a cowl of the engine and take him aside, without disconnecting wires. Remove an air line. Put the car on support so that forward wheels did not concern the earth. Merge oil from a transmission (fig. 4.50). Remove wheels and an antisplash guard of the left wheel. Disconnect from a transmission electric sockets, wires, the selector, a cable of compulsory return gear shifting. Remove shaft of a drive of forward wheels (see further). Remove a starter (see section. "Electric equipment"). Disconnect from a box case маслоприводы. Remove a safety guard of the hydrotransformer and a back cover. Turn on and remove an available bolt of fastening of the hydrotransformer (fig. 4.51). Then by means of a face key and the extension piece turn a pulley of a cranked shaft and turn on
the remained three bolts of fastening of the hydrotransformer to a leading disk as they become available. Establish a support between the central cross-piece and the engine, supporting the power unit. Establish for transmission support a hydraulic jack. Remove back, then left arms of a suspension bracket of a transmission. Unscrew bolts of fastening of a transmission to the engine and take out it through a bottom of a motor compartment, holding thus the hydrotransformer.

Fig. 4.53. Distance check between fastening of the hydrotransformer and a surface of interface of a case of an automatic transmission with the engine: X — should be not less than 21,1 m


At installation of a transmission replace all removed epiploons, rubber rings, laying and самоконтрящиеся nuts. Grease with a thin butter layer of an edge of new epiploons before their installation in openings of an entrance of power shafts of a transmission. Check distance between fastening of the hydrotransformer and a surface of interface of an automatic transmission with the engine (fig. 4.53).
Operations on installation of a transmission carry out as it should be, the return to removal.
After installation of a transmission fill in in its case necessary amount of oil, it is desirable warm. When filling oil the lever of the selector should be established in the situation "N" or "R". Start up the engine. Check transmission work idling the engine and during a trial trip on the car.

«previous page
6.3.4. Adjustment of the selector of a transmission
following page»
6.4. Drive of forward wheels