Removal and installation of the oil pallet of the SR20DE engine. Nissan Almera (from 1995 to 1999 of release)
Nissan Almera service from 1995 to 2000 in N15 body
1. General information
2. The general requirements to car repairs
3. Operation and car maintenance
4. Petrol engines
4.1. Removal and installation of the power unit
4.2. Dismantling and engine assembly
4.3. Block of cylinders
4.4. Shatunno-porshnevaya group
4.5. Cranked shaft and flywheel
4.6. Gazoraspredeleniye mechanism
4.7. Head of the block of cylinders of GA14DE and GA16DE engines
4.8. Head of the block of cylinders of the SR20DE engine
4.9. Cooling system
4.10. Greasing system
4.10.1. Removal, check and installation of the oil pump
4.10.2. Check of pressure of oil
4.10.3. Removal and installation of an oil radiator of the SR20DE engine
4.10.4. Removal and installation of the oil pallet of the SR20DE engine
4.11. System of production of the fulfilled gases
4.12. Power supply system
4.13. Complex control system of the engine (KSUD)
5. Diesel engines
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Electric equipment schemes
 







993f9bf4 993f9bf4 993f9bf4

4-10-4-snyatie-i-ustanovka-maslyanogo-poddona-dvigatelya-sr20de.html

4.10.4. Removal and installation of the oil pallet of the SR20DE engine

Lift by means of a jack a forward part of the car and establish it on supports. Disconnect a wire from the "minus" plug of the storage battery. Turn out nuts of fastening of the protective pallet. Merge oil.

Fig. 2.77. Order of an inhaling of bolts of fastening of the steel stamped pallet


Fig. 2.78. Bolts of fastening of a maslouspokoitelny guard


Remove a reception pipe of the exhaust silencer. Turn out as it should be, the return shown on fig. 2.77, bolts of fastening of the steel pallet. Remove the pallet. Remove a maslouspokoitelny guard, having unscrewed bolts of its fastening (fig. 2.78). Raise the engine by means of a jack, having established it under a transmission, or will hang out by means of roofing felts.
On cars with a mechanical transmission note the provision of a coupling bolt on an arm of a forward support of the power unit. Turn on and remove a nut, then take out a coupling hairpin of a suspension bracket of the power unit. Turn on and remove a nut of a coupling bolt of a back support of the power unit. Turn out and remove four bolts with washers of fastening of the central cross-piece. Lower a cross-piece and take out it from under the car. Remove a lock ring between a back suspension bracket of the power unit and an arm.
On the car with the conditioner turn out and remove bolts of fastening of an arm of the compressor to an aluminum case.

Fig. 2.79. Bolts of fastening of a cover


Fig. 2.80. Order of an inhaling of nuts and bolts of fastening of an aluminum case


Turn out two bolts and remove a flat cover from a case flange (fig. 2.79) to get access to two fixing nuts of an aluminum case. Turn out nuts and bolts of fastening of an aluminum case as it should be, the return specified fig. 2.80.

Fig. 2.81. Removal of an aluminum case by a wraparound of bolts from openings (1) on a case flange in carving openings (2) cases


Turn out two bolts of fastening of a flange of a case of the engine to a transmission boat. Screw these bolts in openings 2 (fig. 2.81). Tighten bolts to separation of an aluminum case from a surface of the block of cylinders then turn out bolts.
On cars with an automatic transmission for removal of a case disconnect a selector cable from a transmission.

Fig. 2.82. Removal of the amplifier of the basis of a cast bed of radical bearings


After removal of a case turn out bolts and a nut of fastening of the filter and a maslopriyemnik, and also the amplifier of the basis of a cast bed of radical bearings of a cranked shaft (fig. 2.82) and remove them. Wash out the mesh filter in solvent. Check a filter grid. In case of malfunction replace a maslopriyemnik assembled with the filter. Check rubber pillows of a support of the central cross-piece of a suspension bracket. On them there should not be wear tracks and damages. In case of need replace rubber pillows.
Before installation clear of hermetic of a surface of interface of the block of cylinders and a case, wipe pure rags a case and an internal part of the engine. Establish a new sealing ring in a groove on the top part of a maslopriyemnik and the filter. Establish the filter on the basis of a cover of the oil pump.

Fig. 2.83. Hermetic drawing on a contour of a surface of an aluminum case


Evenly tighten bolts and a nut of fastening of the filter. Establish the amplifier on a cast bed of radical bearings of a cranked shaft and evenly tighten fastening bolts. On a pure and dry surface of interface of an aluminum case and the block of cylinders put a uniform and continuous layer of hermetic according to fig. 2.83.
Establish a case on the block of cylinders. Establish bolts and nuts of fastening of a case
also tighten them the set moment in the sequence specified fig. 2.80.
Establish two bolts of fastening of a flange of a case of the engine to a case of a transmission and evenly tighten them. On cars with an automatic transmission attach a selector cable. Establish a flat cover on a flange of a case and evenly tighten bolts of its fastening (see fig. 2.79).
On cars with the conditioner establish bolts of fastening of an arm of the compressor and evenly tighten them. Be convinced that rubber pillows of support are established on the places. Establish a lock ring on a back arm of a support of the power unit. Establish into place the central cross-piece, fix it bolts with washers and tighten them the set moment.
On cars with a mechanical transmission establish a coupling bolt with a nut on an arm of a forward support of the power unit. Adjust position of the power unit so that the coupling bolt coincided with a label made before removal. Tighten a bolt the set moment. Establish a coupling bolt on an arm of a back support of the power unit and tighten a nut the set moment. Clean a jack from under a transmission. Establish a maslouspokoitelny guard on the basis of an aluminum case and evenly tighten fastening bolts. Put a continuous equal layer a germetka on a contour of a pure and dry surface of interface of the steel stamped pallet and an aluminum case. Put a hermetic layer in a fillet in the central part of a surface of interface to an aluminum case between openings and round internal edges of openings for bolts.

Fig. 2.72. Details of system of greasing of GA14DE and GA16DE engines: 1 — the oil filter; 2 — щуп for check of level of oil; 3 — the sensor of pressure of oil;
4 — the plug of fastening of the oil filter; 5 — a directing tube щупа for check of level of oil; 6 — a forward cover of a drive of camshafts;
7 — a conducted gear wheel of the oil pump; 8 — a leading gear wheel of the oil pump; 9 — a cover of the oil pump; 10 — the plug of a drive of the oil pump;
11 — a sealing ring; 12 — a maslopriyemnik; 13 — a plunzher of the reduktsionny valve; 14 — a spring; 15 — a stopper of the reduktsionny valve; 16 — an oil case; 17 — a stopper of a drain opening; 18 — the block of cylinders


Establish the steel pallet, acquire bolts by hand, then tighten them in the sequence shown on fig. 2.72. Establish a reception pipe of the exhaust silencer on a final collector. Establish into place the bottom protective guard and evenly tighten bolts of its fastening. Fill in engine oil in the engine.

«previous page
4.10.3. Removal and installation of an oil radiator of the SR20DE engine
following page»
4.11. System of production of the fulfilled gases